NetComposites

Connecting you to the composites industry

Advertisement

Bucher and Ensinger Develop Thermoplastic Connector Mountings for Aircraft Interiors

Bucher and Ensinger Develop Thermoplastic Connector Mountings for Aircraft Interiors

  • Tuesday, 13th November 2018
  • 0 comments
  • Reading time: about 5 minutes

More in Aerospace

Alvant Recognised at BEEA Awards

  • 21st October 2019

Greene Tweed Launches Fusion 665

  • 16th October 2019

Evonik Adds to the TROGAMID(r) Product Group

  • 15th October 2019

Bucher Leichtbau and Ensinger have collaborated in a project to showcase the advantages of thermoplastic composites in an aircraft interior application.  

Lightweight and high-strength materials have become indispensable for high-end applications in the aviation industry. In passenger aircraft every kilogram counts, which is why metals are increasingly being replaced with plastics-based solutions. Thermoplastic composites, in particular, offer companies kitting out aircraft significant weight reduction without requiring them to make compromises in terms of mechanical properties.

Bucher, headquartered in Fällanden, Switzerland, is a specialist for aircraft interiors and automotive equipment. Among other things, the group’s aviation division develops and produces galleys and cabinets for passenger aircraft. A full module of this type can accommodate a load corresponding to eight times its own weight and has to be able to withstand accelerations that are at least nine times that of gravitational acceleration. A distinction is drawn between flight loads (normal flight conditions such as take-off, landing, turbulence) and emergency landing loads (controlled emergency landing or aborted take-off). The required minimum operating life of the modules is 25 years for Airbus and Boeing.

Material and installation costs

For safety reasons, all metal mountings for electrical plug-in connections in commercial aviation must be earthed. With electrically conductive, supporting structures in the Bucher aluminium galleys, an existing fastening screw equipped with the necessary corrosion protection measures is often sufficient. If, however, the metal connector mountings are positioned on non-conductive structures in the galleys, an additional cable is required for the electrical earthing. This earthing cable must be secured at regular intervals which drives a requirement for additional fastening threads, spacer bolts, cable clamps and screws.

In addition to the material input for the cable routing, high costs arise for planning and installation. The design work includes making an entry in the schematic circuit diagram; in addition, a resistance measurement must be defined in the test plan for every earthing cable. This must also be incorporated into the relevant maintenance guidelines and operating instructions, as well as into the authorisation documents. During production, the contact resistance must be recorded and a corrosion protection coating be applied with every earth connection.

Metal substitute removes the need for earthing. The work and costs involved in an earth connection can be completely eliminated if the connector mountings previously made from metal are replaced by a non-conductive version. Because of the operating temperature and fire safety requirements, however, it is not possible to use a low-cost, standard plastic.

For Bucher, the sought-after alternative needed to be capable of replacing a large number of existing sheet aluminium parts one-to-one so as to minimise the work and costs involved in switching. For this demand to be met, a rigid, high strength material is required.

Owing to the relatively small quantities of the different connector mountings, a solution with high tool costs was not an option. Initial trials with locally remodelled parts made from fibre reinforced thermoplastic sheet material did not show satisfactory results.

Thermoplastic solution

The breakthrough was achieved in collaboration with Ensinger, based in Otelfingen, Switzerland. On the basis of Bucher’s specifications, Ensinger developed a solution based on a prepreg approved for the aviation industry with glass fibre reinforcement and a PEI (polyether amide) matrix. After a brief optimisation phase, it was possible to manufacture the first series-produced parts.

Two of the Ensinger’s sites are involved in the production of the connector mountings. At Otelfingen, Ensinger produces semi-finished parts in an angular shape from the PEI prepregs. Unlike comparable components, these blanks are not cut to size from a thick laminate and thermoformed but, using individual prepreg layers, pressed in a tool into the defined form. Among other things, this process offers the advantage of reducing the springback effect. The CNC processing of the composite parts takes place at Ensinger’s subsidiary Trig Engineering in Bridgwater, Somerset, UK, which operates in accordance to the aerospace AS9100 revision D standard. From the angular blanks produced in Otelfingen, Trig precision machines the connector mountings to final product specification.

For most fastening brackets there are several versions with different dimensions. Thanks to the flexible process, it is also possible to produce high-quality, special designs with contours or drilled holes and with short lead times.

Simpler, cost-effective, lighter

The manufacturing costs for the new plastic mountings are significantly higher than the previous version in aluminium. However, the savings in terms of engineering and production of the cabinets means that the new solution is still considerably more straightforward and more cost-effective overall. As the galleys are lighter thanks to the use of composite components, the airlines benefit in the long term because every kilogram of additional weight which does not have to be taken into the air saves money.

Thanks to Ensinger’s preform technology, differences in wall thicknesses are also possible when producing angles. The corner section under high strain can be reinforced, while in the sections which are not under as high strain (e.g. on the arms), material can be conserved. The manufacturing technique is referred to as the ‘near net shape’ process. Depending on the component geometry, significant material and weight savings are possible with this technology, whilst maintaining comparable strength and rigidity.


Image provided by Ensinger


For more information visit:


Share this article


Categories


Related News


Comments (0)

Sign in or create an account to join in the discussion.

Leave your comment

Upcoming Events

Advertisement

Advertisement

Advertisement

Follow us
Subscribe to our email newsletter

Subscribe to receive our weekly round-up of all the industry's latest news, jobs, events and more!

We'll always keep your personal details secure and will never share them with third parties for marketing purposes. You can unsubscribe at any time. For further details on how we may use your data, please visit our Privacy Policy.