NetComposites
Juniar Spraybooths

Vyncolit and Sumitomo Bakelite Summit Highlights Need for Lightweighting Powertrains

22 May 2018

Vyncolit and Sumitomo Bakelite Summit Highlights Need for Lightweighting Powertrains

Powertrains, be they conventional, hybrid or fully electric, will need to be light in weight if carmakers are to meet the stringent regulations on carbon dioxide emissions (CO2) to come into force in 2025 – and composites will be key to making this happen. This was the message highlighted at the Lightweight Composite Solutions Conference organised by Vyncolit and Sumitomo Bakelite Co Ltd and held in Gent, Belgium.

The conference was attended by over 50 experts from leading OEMs, suppliers and research institutes in automotive lightweighting, including Nissan Motor, Volkswagen, Renault Nissan Mitsubishi, FEV Europe, Brembo, Robert Bosch, Mahle Filtersysteme, KraussMaffei and the Fraunhofer Institute for Chemical Technology (ICT).

The automotive industry is on the cusp of some dramatic changes. Increasingly stringent regulations on carbon dioxide emissions are driving a move away from vehicles with conventional internal combustion engines to those with hybrid and fully electric powertrains. For example, in Europe, the fleet average emissions to be achieved by all new cars in 2021 is 95 g of CO2 per kilometre. By 2025, this could be reduced further to 75 g of CO2 per kilometre. The average emissions level of a new car sold in 2016 was 118.1 g of CO2 per kilometre.

With the powertrain accounting for 32% of an electric vehicle’s weight, reducing this figure will be key in enabling these vehicles to travel further on a single charge and allowing smaller and cheaper batteries to be used.

“All OEMs, have a lot of work to do in the next six to seven years,” Pieter Vanderstraeten, Managing Director of Vyncolit, told conference delegates. “Lightweighting will be key in hitting these targets, regardless of the drivetrains employed. For electric vehicles, there are few standard technologies and limited means for the true mass production of electric motors. The need for regenerative technologies, small city cars and autonomous vehicles will change the requirements of braking technologies. All of these present opportunities for lightweight composite solutions.”

Nissan’s General Manager of Planning Group, Powertrain Technology and Prototype Development Department, Kimio Nishimura, outlined the OEM’s mid-term plan – M.O.V.E to 2022 – to accelerate the electrification of its vehicles in order to hit the CO2 targets. He highlighted the need for compact, efficient and powerful motors, and heat-resistant, thermally conductive and low-permittivity materials for their construction.

Sumitomo Bakelite has developed a portfolio of materials and processing expertise that enable its partners to not only reduce the weight of their powertrain parts in comparison with metal solutions, but also save money through the opportunities plastics present for integrating many functions into a single component. For example, Fraunhofer ICT’s Lars-Fredrik Berg talked delegates through the DEmiL project, the aim of which is to develop a direct-cooled electric motor with an integrated lightweight housing that delivers power on a consistent basis. A highly-filled, low-viscosity epoxy from Sumitomo Bakelite is used to overmould the motor’s stator. Channels are formed during this transfer moulding process that help to cool the active materials, helping to produce a motor with a very high weight-specific power output.

In internal combustion engines too, there is still a significant scope for lightweighting using composites, thereby lowering fuel consumption and CO2 emissions. Group Leader for Composite Materials at Robert Bosch, Gerrit Hülder, outlined the company’s work replacing aluminium fuel pumps with those made from plastics. Not only did this switch of materials lead to a weight saving of 40%, it also cut costs by 30% through a reduction in part count.

Vyncolit's Chief Innovation and Technology Officer, Hendrik De Keyser, told delegates that the use of phenolic resin for the manufacture of brake pads can slash the weight of the brake systems in a car by 1 kg.

“Two thirds of innovations are based on developments in materials science,” stated conference chair and Fraunhofer ICT Institute Leader, Frank Henning. “Materials seem to be old economy, but they are enablers of the new economy.”


Photo provided by Vyncolit NV and Sumitomo Bakelite Co Ltd





Related / You might like...

Continental Structural Plastics Adds SMC Line in France

Continental Structural Plastics (CSP) will install a sheet moulding compound (SMC) production line at its facility in Pouance, France, to support the need for its composite formulations in Europe.

Solvay Breaks Ground on Aerospace Composites Facility Expansion in Texas

Solvay has celebrated the groundbreaking of its Greenville, Texas, US, manufacturing footprint expansion that increases the site’s resin mixing capacity to meet the growing needs of commercial and military aerospace composite customers.

Premium Aerotec, Faurecia and Solvay Launch Thermoplastic Composites Consortium

Premium Aerotec, Faurecia Clean Mobility and Solvay have launched the research group IRG CosiMo: Composites for Sustainable Mobility, which will focus on the development of materials and process technologies to enable the high volume production of thermoplastic composites for the aerospace and automotive markets.