NetComposites
Advanced Engineering 2018

Tepex Thermoplastic Employed in Off-road Vehicle Interior

29 August 2017

Tepex Thermoplastic Employed in Off-road Vehicle Interior

Tepex dynalite thermoplastic composite is being employed in the backseat system of a European automotive manufacturer's off-road vehicle.

The centre backseat is equipped with a load-through that enables the backrest of each seat to be folded down individually. This load-through component is produced by shaping and back-injecting Tepex dynalite.

Tepex is manufactured by LANXESS subsidiary Bond-Laminates, based in Brilon, Germany.

“The part marks the entry of this composite material into the lightweight design of backseat systems and is further evidence of its enormous potential in series production applications,” says Henrik Plaggenborg, Head of Technical Marketing & Business Development, Tepex Automotive.

“The new component is more than 40% lighter than its steel counterpart," explains Harri Dittmar, Project Manager and Tepex Applications Specialist. "At the same time, this safety-relevant component withstands all load scenarios, because the orientation of the continuous fibre layers in the only 2 mm-thick semi-finished product is designed to bear the mechanical stress.”

The component was developed by Brose Fahrzeugteile with support from the LANXESS High Performance Materials business unit. Brose manufactures the component at its site in Coburg, Germany.

For functional reasons, the load-through is only mounted on one side, at the top of the rear seat’s backrest. Because of its position, it is exposed to both bending and torsion forces. To withstand these load scenarios, a multiaxial design was chosen for the continuous-glass-fibre layers in the thermoplastic composite. Multiaxial Tepex is a new development from Bond-Laminates, which makes the composite sheets significantly stronger than before by combining the Tepex fabric with tapes. The semi-finished product for the load-through has a core consisting of four layers, each 0.25 mm thick, which have a fibre orientation of ±45° relative to the component’s longitudinal axis and are arranged symmetrically. They absorb the torsion forces. In contrast, the bending forces are absorbed by the two outer layers, each 0.5 mm thick, in which 80% of the continuous fibres are in the direction of force.

“In case of a frontal collision, this multiaxial layer design ensures that the lightweight component withstands the impact of the accelerated load in the trunk and, in case of a rear collision, the inertia forces pressing the passenger into the seat,” explains Dittmar.

To manufacture the load-through, a blank of the semi-finished product is heated, placed in the injection mould, shaped and back-injected with a glass fibre reinforced thermoplastic. In addition to ribbing that lends the part high stiffness, numerous functional elements are moulded on the component in the injection moulding step, such as mounts for the headrest, various mounting points and screw connections, and the surrounding groove to which the rear, textile covering of the load-through is mounted. With a conventional steel design, this component would have had to be welded or screwed on separately.

The mould for the load-through was optimised with the help of a draping simulation developed by LANXESS as part of its HiAnt services. Various shaping strategies were visualised and evaluated in the draping simulation. The results were incorporated in mould design from the outset and helped to reduce the development time. LANXESS derived the design of the semi-finished product blank on the basis of the specific mould technology. The blank is pre-shaped or locally held in place inside the mould before the mould is fully closed. This prevents the formation of folds and the over-extension of the fibres during shaping.


Photo provided by LANXESS




Share this story


Related / You might like...

Cobra International Exhibits Product Range at CAMX 2018

Cobra International will showcase a range of composite products at CAMX 2018, including carbon fibre components for the automotive, transportation, marine, water sports and luxury sectors.

Metyx Expands Warehousing Facilities in Hungary

The Metyx Hungary factory, located in Kaposvár, has recently expanded its warehousing facilities, adding an additional 3,024 m2 of enclosed storage space for composite technical fabrics, packaging and FRP tooling.

Chomarat Reinforcements Feature in Live Demos at CAMX 2018

A skateboard, architectural panels and a rigid roof for boats, all built using Chomarat composite reinforcements, will be on display at CAMX 2018.