29 November 2016
29 November 2016
Fenstür Windows and Doors, a manufacturer and direct retailer of high-end custom-built residential wooden doors and windows, has begun replacing fibreboard cores in its doors with a unique composite core produced by RhinoKore Composite Solutions.
According to RhinoKore, the composite cores offer a number of benefits, the most important of which is more than halving door weight, which eases handling and installation of the door at the construction site, plus brings the carry-over benefits of mass decompounding, such as being able to use smaller and lighter hardware to hang the doors. Additionally, it says that the new cores improve dimensional stability and thermal insulation (R value is 3.15 to 3.19 per 1 inch/2.5 centimeter thickness), and they also proved to be a drop-in replacement during the manufacturing process without a need to modify anything, including the adhesive.
The collaboration began at the recommendation of a local builder who was working on a residential construction project where Fenstür was asked to produce a custom interior door for a walk-in cooler. The homeowner, an avid hunter, wanted a cold room with a hidden door to hold game, food, and wine. RhinoKore explains that the unique oversize door is designed to blend into the wall when closed, hence it features concealed hinges and a removable spindle that functions as a handle. The side of the door facing the inside of the cooler is finished in birch wood to match the cooler interior, while the outside (exercise room-facing side) of the door is covered with hackwood to match floors and walls in that room.
The door was built before the exterior/exercise-room was paneled with hackwood. Wood for that side of the door was brought to Fenstür's shop and laid out across the door and marked. Board offcuts were then made and labeled so they could be attached to the walls adjacent to matching boards on the exterior/warm-room side of the door. This extra effort allowed the team to "board match" paneling on the exterior of the door so the grain lines up and continues onto the walls, helping the door blend even better into the exercise room.
Due to the significant differences in both temperature and humidity anticipated between the cold/dry cooler-facing side of the door and the warm/humid exercise room-facing side, the Fenstür team says it knew the door would need to be thicker than normal (2.25 inches/5.72 centimeters) to provide insulation. However, a door that thick and large (42 by 84 inches/107 by 213 centimeters) using a conventional fibreboard core was also going to be very heavy, which would bring numerous challenges. That's when the local builder mentioned RhinoKore's unique composite core as a possible solution to replace the heavy fibreboard.
RhinoKore says that the patented honeycomb core is made from a tough, heavy-duty fabric woven with nylon (polyamide) and polyester fibres. The fabric is fed into a custom-built "honeycomb" machine where it is quickly exposed to hot air (427°C/801°F), which heats and softens the fibres and allows them to be manipulated and formed easily. The fabric is then pressed into sheets of conjoined hexagonal cells (13 mm/0.5 inch in diameter with 1.1 mm/0.04 inch walls) and cooled. Next, the solidified honeycomb sheets (122 centimeters/4 feet wide by 244 centimeters/8 feet long by 152 mm/6 inches thick) are removed and placed in a mould, where a two-part, closed-cell polyurethane foam is injected into all the cells and allowed to cure in a heated press. The finished core is then sliced to thicknesses ranging from 0.25 to 6.0 inches/0.64 to 15.2 centimeters and then can be bonded to faceskins of thermoplastic or thermoset composite, metal, wood, or even concrete. RhinoKore claims that the honeycomb core has a very-good stiffness- and strength-to-weight ratio and helps improve the structural integrity ― especially torsional rigidity ― of any structure to which it is bonded. It is dimensionally stable and provides very-good compression and shear strength, as well as thermal and acoustical insulation. At any thickness, the core offers excellent impact strength (energy absorption/damage tolerance). And unlike fibreboard, it is impervious to water and will not trap moisture or rot. It also is much lower in density than fibreboard, which helps reduce part mass significantly.
"We ended up trying the RhinoKore product on the cooler door for a couple of reasons," explains Braden Gierc, Fenstür General Manager. "We'd had some weight issues with the overly large front door to this house, so we opted to use the lighter core for the cooler door, which was also oversize. The new core gave us added dimensional stability and resistance to warpage and cracking, which we felt was really important given the significant temperature and humidity differences on either side of the door. The cold/dry side of the door wants to shrink, while the warm/humid side is in a different dynamic equilibrium. And the fact that the core is insulated is a bonus, as it helps make the cooler and its door more energy efficient."
The Fenstür team built the door using the composite core and found that it was a drop-in replacement for the fibreboard they'd previously used. Nothing had to be changed in the production process ― even the adhesive (polyvinyl acetate (PVA, also known as white carpenter's glue)) they had previously used to bond fibreboard to wood faceskins could be used with the honeycomb core. The final door consisted of 0.75 inch/1.9 centimeter-thick layer of hackwood paneling on the outside, a 1 inch/2.5 centimeter-thick composite core, and a 0.5 inch/1.3 centimeter-thick layer of birch paneling on the inside. Once the new door was assembled, Fenstür's carpenters and finishing specialists were amazed to see that it was less than half the weight it would have been with a fibreboard core. It also was quieter and took less effort to open and close. The team knew that that would not only make it less costly to ship to the work site, but would make it easier for the local builder's construction crew to hang and true the door. They also felt that door sag would not be an issue, since the hinges were not stressed thanks to the reduction in door weight.
"The weight reduction is really significant," notes Gierc, "On a conventional 50 by 100 inch (125 by 250 centimeter) door that can weigh 400 to 500 pounds (181 to 227 kilograms) with a fibreboard core, we can now reduce the weight to about 150 pounds (68 kilograms). That's a benefit to anyone who touches the door and is definitely going to make the installer's job a lot more pleasant. Not only does it reduce the risk of ending up with a door that lists to one side once hung, but it also reduces the chance of a door getting dings and dents as it's moved around, and it reduces the risk of warping and cracking too. It gives everyone some added peace of mind."
Owing to a positive experience with the new core on the cooler door, the Fenstür team built several prototypes. They then offered the new core as an upgrade at no additional cost to the first few customers to see how well it would be received. "To date, no one has turned us down," says Gierc. "In fact, we've already sold four doors and have another nine doors on order using this core."
The only downside Fenstür says it has seen is that because the core makes doors significantly lighter and also provides sound damping, it eliminates the heavy clunk traditionally associated with a door closing and with someone knocking. "We've even tried bonding quarter-inch (6.35 mm) plywood between the core and the skins to solve the sound issue, but the door still stayed very quiet," adds Gierc. "Some customers don't like the change, but others couldn't care less."
Going forward, the company plans to offer the composite core as a premium upgrade for a modest cost increase and will begin experimenting to see if it can be used for windows as well. Access to the technology has made company management more confident in bidding on very-large doors, which could open up a new market segment for them. "You could say that now that we have access to this core," explains Gierc, "it's given us new bragging rights because it allows us to build oversize doors and still maintain dimensional stability without losing strength. In fact, we're gaining strength and we're able to achieve something that previously was very challenging. This means we're now better equipped to address the creative projects architects and homeowners imagine. That makes it a win-win situation."
"The new business with Fenstür Windows and Doors is a welcome addition to the RhinoKore Composite Solutions family," notes Robin Arnold, RhinoKore President. "The foundation of our company was built on the principle of creating innovative solutions for specific needs. Our work with Fenstür is a perfect example of this principle in action."
Australian organisations Austrak, Laing O’Rourke and the University of Southern Queensland (USQ) have joined forces to develop polymer composite solutions for bridge transoms in a $10 million project titled Polymer Composite Transoms for Rail Bridge Deck Replacement (CompTrans).
Composites One and the Closed Mold Alliance, along with more than 15 industry partners, will demonstrate the latest advancements in closed moulding and advanced processes for building real-life parts for marine, aerospace and other markets during CAMX 2018 in Dallas, Texas, US, on 16-18 October.
With its new ‘Process Live’ format, processing and manufacturing processes will become a visible focus of this year's Composites Europe exhibition in Stuttgart, Germany, on 6-8 November. Mechanical and plant engineering companies will get together in group exhibits to showcase their technologies in live interactions, enabling visitors to experience sub-processes in a larger context.