NetComposites
Juniar Spraybooths

Victrex Launches Composites Designed For Aerospace: Victrex Ae250 Product Family

27 October 2015

Victrex has launched unidirectional (UD) tape and laminate panel composites for the aerospace industry, introduced under the brand VICTREX AE250 composites.

According to Victrex, the new product group enables the production of continuously-reinforced components that can perform under load.

Such components include brackets, clips, clamps, and housings used throughout the aircraft in primary and secondary structures. The development and launch builds on the hybrid moulding technology released in 2014 and also serves as proof that Victrex is moving forward in the supply chain to provide enhanced solutions.

Victrex explains, one compelling advantage of implementing a PAEK-based composite solution is faster manufacturing as a result of smarter designs, contributing to cost savings, and improved installation times. VICTREX AE250 composites says it has also shown a weight savings of up to 60% under certain circumstances when compared to metals such as aluminum, stainless steel, and titanium. That weight reduction translates directly into significant gains in fuel-efficiency and reduced CO2 emissions. The composites have also shown an up to 5x higher specific strength compared to those of metals.

“Victrex sees this as another excellent opportunity to support our customers by being a total solutions provider,” noted Tim Herr, Aerospace Director at Victrex. “Our innovative PAEK composites, paired with the revolutionary hybrid moulding technology, bridge the gap between composites and injection moulding. It enables the manufacture of complex composite parts which have not been possible until now.”

With VICTREX AE250 composites being used as inserts in existing injection moulding equipment, the hybrid moulding process enables the overmoulding of a continuously-reinforced thermoplastic composite with VICTREX PEEK injection moulding polymers. The hybrid moulding technology offers major advantages, including improved cycle times, lower energy requirements, and the elimination of scrap and secondary operations. These factors help to reduce total system cost, a high priority in the industry's effort to move planes off the assembly line faster and more cost-effectively. Analysts believe that more than 35,000 new aircraft will be needed over the next 20 years in order to replace ageing fleets and to meet civilian flight demands.

“One key to achieving this is the replacement of metals and thermosets with next-generation thermoplastic solutions. When Victrex collaborates with our customers from concept to final part, they are able to achieve an unmatched combination of cost reductions, weight savings, design freedom, strength, and production speed for next-generation thermoplastic components.  All of these are becoming increasingly valuable to both the air-framers and tier suppliers alike," explains Tim Herr.

Compared to thermoset solutions, PAEK composites can be processed faster, using out-of-autoclave methods, and are 100% recyclable. They have better damage tolerance than thermosets and offer greater chemical resistance, fatigue performance, and FST (flame/smoke/toxicity) properties, while matching the strength and stiffness of thermosets. In comparison to metals, corrosion resistance, processing speed, and thermal insulation are improved, while impact resistance and damage tolerance will be similar.

Victrex says that key features of its VICTREX AE250 composites also include outstanding high-temperature performance and thermal stability, a wide-ranging chemical resistance to aerospace fluids and gases, and excellent resistance to hydrolysis and corrosion. Victrex has solely focused on the development of PAEK-based solutions for more than three decades and consequently been able to partner in the automotive, aerospace, energy, electronics, and medical industry with leading companies around the world.






comments powered by Disqus

Related / You might like...

NetComposites and ACMA Announce Dates for Global Composites 2018

Global Composites, a new international conference jointly hosted by NetComposites and the American Composites Manufacturers Association (ACMA), will take place at Caesars Palace in Las Vegas, US, on 27-28 June 2018.

Thai Flight Training Orders Spatial A320 Door Trainer

Thai Flight Training (TFT), a subsidiary of Thai Airways, recently ordered an Airbus A320 door trainer from Spatial Composite Solutions.

ACMA Champions Policies to Advance Composites in Infrastructure

At the American Composites Manufacturers Association (ACMA)'s third annual Infrastructure Day on 6-7 February 2018 34 ACMA members joined together to meet with over 100 Members of Congress and their staffs to advance legislation to drive investment in innovative material solutions for transportation, water and energy infrastructure.