25 August 2006
25 August 2006
Carbon fibre rods supporting this tiny mirror can be made to bend up to 90 degrees millions of times without showing fatigue. The technology could be used to create a video projector on a chip.
For decades, researchers have been trying to make video displays using tiny mirrors mounted on silicon oscillators. But silicon won't oscillate fast enough and bend far enough.
""You need something incredibly stiff to oscillate at a resonant frequency of 60,000 times a second (the line-scanning rate of most video displays), but it also needs to bend a lot for adequate image size,"" explained Shahyaan Desai, a Cornell graduate student who has been working for more than three years to create a practical MEMS video display device.
So Desai and his Cornell colleagues have turned to carbon fibre, the same material used to reinforce auto and aircraft body parts, bicycle frames and fishing rods.
""Carbon fibre is twice as stiff as silicon but 10 times more flexible,"" said Desai.
He is first author of a paper with Michael Thompson, Cornell associate professor of materials science and engineering, and Anil Netravali, Cornell professor of fibre science, on using carbon fibers in MEMS, published in the July issue of the Journal of Micromechanics and Microengineering.
Carbon fibres are made of thin, narrow sheets of graphite that roll up and clump together to form fibers. For industrial uses the fibres are embedded in plastic to form composite materials that are stronger than steel, yet lighter. Desai's MEMS are made with the raw fibres.
Desai first showed that micrometer-scale carbon fibres can bend like tiny fishing rods by more than 90 degrees and can be made to vibrate billions of times without breaking down. ""This is, to our knowledge, the first material to even approach such large deformation at high frequencies without observable fatigue,"" the researchers wrote in their paper.
""Carbon is normally a brittle material,"" Desai said, ""but in the fibre form it resists breakage. We have some data implying that if it lasts three and a half days it's going to last forever.""
Desai then built an optical scanner consisting of a tiny rectangular mirror measuring 400 by 500 microns, supported by two carbon-fibre hinges about 55 microns across. Made to oscillate at 2.5 kHz, the tiny mirror caused a laser beam to scan across a range of up to 180 degrees, corresponding to a 90-degree bend by the carbon fibres.
An oscillating mirror could be used to scan a laser beam across a screen, and an array of mirrors, one for each horizontal line, could produce an image in the same way that a moving electron beam creates an image on a television screen.
""It would be an incredibly cheap display,"" Desai said. And the entire device would be small enough to build into a cell phone to project an image on a wall.
Besides serving as oscillators, the researchers said, carbon fibres could be made into clock springs that either unwind slowly to power a micromachine over a period of time or unwind rapidly to provide a sudden burst of power, or used as micro-sized pendulums that could harvest energy from motion like a mechanical self-winding watch to make cell phones, PDAs and even watches that are powered by the user's movement.
Sumitomo Chemical reports that its polyethersulfone (PES) micro-powder additive SumikaExcel 5003P boosts fracture toughness and resistance to micro-cracking for fibre reinforced epoxy composites over a broad temperature range without negatively impacting dimensional stability, flame/smoke/toxicity (FST), creep resistance, modulus, impact, or yield strength.
Renault, Webasto, ARRK-Shapers and Polyscope Polymers won the People’s Choice award for the most innovative composite part at the 18th annual Automotive Composites Conference & Exhibition (ACCE) sponsored by the Society of Plastics Engineers (SPE).
ZSK will hold its bi-annual technology showcase on 21-22 September 2018 at its Krefeld, Germany, headquarters. The Embroidery Technology Show assembles more than 25 exhibitors from around the world to discuss emerging trends in the embroidery manufacturing industry and demonstrate the latest products produced using techniques such as tailored fibre placement (TFP) or smart textiles.